Shop Mobile More Submit  Join Login

Similar Deviations
Organized by Artist
again a part with a lot of pieces :aww:
the first five screenshots are again the pieces which are for the hip

i promissed that i make a few photos of this boosters
well, these are a bit more complex as the others but base on the same technique

first i cut them out and build the single rings
i also removed the tabs for the inside ring
quite useless for me
at the fourth photo you can see the final pieces
because the sheets are designed for colored cardboard paper there are no tabs for the bottom piece where the peak as to be attached on
so i just colored a little paper piece with black marker and glued it on top (you can see it at the left piece)

then i put some glue at the inside of the tube and put it on top of the inside ring
after it's dry, i add the peak
quite simple, if you know how it works ^^;

piece overview 1
as always, here are all pieces what you need for the hip

po2
again one of those problems when you work with normal paper
to combine this pieces i just add a little tab at the backside and cut two lines into the base piece

po3
this one took me really long to figure out
first i thought the smaller piece has to be attached to the hip base but that doesn't work
because the black flat pieces where all the parts has to be attached fit exactly to the hip base
so this was the only solution

i scratched the color where this pieces has to be combined

po4
lego is just boring against this :D

po5
and e viola
the final hip :meow:
Show
Add a Comment:
 
No comments have been added yet.

after one year of papercraft
my tool collection growed a bit
meanwhile i got a lot more stuff and i wanna share it with you

bottom, from left to right:
-a normal cutter for rougher steps
-a precise cutter for fine steps
-my good old freaking sharp scissor from the drug store :D
-a flat tweezer to fold bigger edges and taps
-a thin tweezer to fold fine edges and taps, also to remove the glue
-the tweezer what i used the most time to press the taps together, very efficient because of the angle and the flat ending

-steel cords to put small amounts of glue on the taps, meanwhile i have two of them, a long and a short one, i found this pieces on the street, these things normally are from the bristle of a street cleaning machine
sometime they broke and lay on the street
i cleaned and polished them that the glue don't stick

top, from left to right
-some chains, i used them to get some weight into the models that they stand on there own
-yes, Allen keys, i use them as weight and to reach some places inside of a model
-some cross tweezers, very handy, specially when you have to glue some rings ore don't have the modd ore/and time to hold the pieces
-some woodsticks, as contrast to the q-tips, much more better, because the glue stick and hold on them. they are also very usefull to get some distance for "flying parts" ore as a stabilization at the inside of a model
-two steel ruler, one long and one with some curves
-and at least a pencil :meow:
Show
Add a Comment:
 
No comments have been added yet.

cats to free fella hu ?
you can have it :evillaugh:
Show
Add a Comment:
 
No comments have been added yet.

Hello again! :D
It's been a while. Well, this is my version of the Medabot known as Rokusho. I made this because It was part of my childhood, and I saw the Metabee papercraft long ago, (I think the designer should be more known). Anyhow, I just couldn't resist making it.

4 Shared:
[link]

RapidShare:
[link]

Mediafire:
[link]

It contains PDOs, PDFs, and photos.

Hope you enjoy making it! :D
(I'm not planning on making any other medabot by now, at least not until I finish all the projects I have in mind)

Thank you everyone for the Favs! It's much appreciated n_n

Medabots is (c) Bee Train and the creator/directors.
Show
Add a Comment:
 
No comments have been added yet.

Hello There!

Arcbeetle from the anime Medabots turned into papercraft!

I know I should have uploaded this a few days ago, but I couldn't make a really fast build. Anyway, there aren't many difficult pieces, just maybe a difficulty with the balance, but it depends on what glue you use.

The .rar contains 1 PDF, 1 PDO and a text file.

Mediafire: [link]

Medabots is (c) Bee Train and the creator/directors.
Show
Add a Comment:
 
No comments have been added yet.

Well, this is my version of the XXXG-01WK, Also known as Wing Gundam Ka Ver.

The Rar contains: PDOs, PDFs, Photos of the making (as a kind of “guide”), and a personal opinion.
Thanks to my friends and family for being there to make everything less boring lol :D
and a Special Thank to all the creators of this Awesome anime.

4Shared link:
[link]

RapidShare:
[link]

Mediafire:
[link]

Thanks everyone for the Favs! It's much appreciated n_n

Gundam is ⓒ Sunrise/Bandai/Sotsu Agency
Show
Add a Comment:
 
No comments have been added yet.

Yayyyy. another Darknut builder : ] (why the long face?) oh yea, I forgot to put the other views. here they are:

Back view:[link]

Side view:[link]

No armor:[link]
Show
Add a Comment:
 
No comments have been added yet.

Yay new papercraft (Again!) I'm not doing multiple photos in one anymore(PICEPTION), so I'll instead put views:
Show
Add a Comment:
 
No comments have been added yet.

here you go,demonreapergirl. skywawrd sword gaurdian! the template is alright, but attaching the limbs were a problem. sorry no mace, I'll get it done as fast as I can.
Show
Add a Comment:
 
No comments have been added yet.

Papercraft Model is designed by ~fezco
Horne (ホルン Horun, not to be confused with Kingdom of Horun) is a Moogle in Final Fantasy XII. Part of the Moogling service operated around Rabanastre, his siblings are Hurdy, Gurdy, Nono, Sorbet, and Montblanc, making him one of the Six Moogle Siblings. His other siblings are also involved in other jobs; Gurdy assists players in renting Chocobos; Nono serves as Balthier's head mechanic; Sorbet and Hurdy operate Moogling posts with him; and Montblanc is the founder of Clan Centurio, which specializes in the hunting of Elite Marks.
Info: [link](Final_Fantasy_XII)
Papercraft: [link]
*Pom-pom not part of the template.
©Square Enix
Show
Add a Comment:
 
No comments have been added yet.

Papercraft Model is designed by ~fezco
Montblanc is a recurring character in the Ivalice Alliance. He is a hard working moogle, and in all his appearances, he is in charge of a clan. In Final Fantasy Tactics Advance, he found Marche Radiuju after St. Ivalice transformed into the land of Ivalice and later decided to help him revert Ivalice back to normal. In Final Fantasy XII, he is the leader of Clan Centurio and gives Vaan various Hunts. He is also the oldest one of Six Moogle Siblings, the others being Nono, Hurdy, Gurdy, Horne, and Sorbet.
Info: [link]
Papercraft: [link]
*Pom-pom not part of the template.
©Square Enix
Show
Add a Comment:
 
No comments have been added yet.

Papercraft Model is designed by ~fezco
Nono (ノノ Nono) is a recurring Moogle in the Ivalice Alliance. In all of his appearances, he is always the younger brother of Montblanc, which makes him one of the Six Moogle Siblings. Nono is always involved with airships in one way or another.
It should be noted that his outfit in all of his appearances resembles a green color swap of the game's Tinker Job.
Info: [link]
Papercraft: [link]
*Pom-pom not part of the template.
©Square Enix
Show
Add a Comment:
 
No comments have been added yet.

You have no idea how hard it was to make this picture.

1. The frickin crafts are ENORMOUS!
2. there's not a big enough piece of paper to make them both fit

I had to get o pieces of each color, and put them both together to get the background.

Nevermind that, i need to scale these down anyways. They are too big.

Both of these designed and built by :iconsabi996: AKA me :P

Will be released sometime on [link]

Please check out my first made from scratch video [link]

Also please comment :D ....
Show
Add a Comment:
 
No comments have been added yet.

This is not the official pic yet. This is just a preview i nedd your opinion to finish.

This looks Horrible! If you zoom in you might be able to see the yellow eyes. Too much grey here, and it brought out the red, so i reduced saturation a bit.

Where would i be without photoshop.

Btw. build by me.
Show
Add a Comment:
 
No comments have been added yet.

You already saw previews of jolteon and flareon, but now all three are finished.

All four designed and built by :iconsabi996: AKA Me :P

Let's see: the most difficult parts were: flareon's tail, jolteon's mane, Eevee's fur, and vaporeon is as simple as they come.

They are probably in scale.

Plz check out my first made from scratch video : [link]

These will be available on [link]
Show
Add a Comment:
 
No comments have been added yet.

SMT Jack Frost Papercraft
official nintendo model, dont remember where i get template
Show
Add a Comment:
 
No comments have been added yet.

only 6 pages left - stupid accessories
Show
Add a Comment:
 
No comments have been added yet.

Royal knight complete
source: [link]
Show
Add a Comment:
 
No comments have been added yet.

Prop updates will be posted at GS Props

I accidentally hit the sword against something at the con and it has to be repainted....I feel kinda horrible since it was pretty deep and it now has to be repainted the whole thing, bc of the clear coat.

Sword was mostly made by ~Dionysus80. The blade is made out of wood planks glued together with an aluminum rod in the middle. Shaped with a belt sander. The hilt is made out of styrene, MDF, and the guard is made from tow casted plastic pieces. ~Dionysus80 made one side, then we made a mold and casted the two sides to make the whole guard. The other hilt pieces are lathed and the end one contains the battery and switch. Painted with automotive paint.

Collar is made out of expanded pvc and styrene, finished off with automotive paint

Anime: Saint Seiya: The Lost Canvas
Character: Alone (Hades)
made by: :icondionysus80: and :iconmarikasan:





:star: Facebook :star: GS Props :star:
Show
Add a Comment:
 
No comments have been added yet.

*cough maria sux at taking pics cough*

Prop updates will be posted at GS Props

This is exactly how the sword photographs with out any glow effect in post processing.

This is close up of sword hilt, was mostly made by ~Dionysus80. The blade is made out of wood planks glued together with an aluminum rod in the middle. Shaped with a belt sander. The hilt is made out of styrene, MDF, and the guard is made from two casted plastic pieces. ~Dionysus80 made one side, then we made a mold and casted the two sides to make the whole guard. The other hilt pieces are lathed and the end one contains the battery and switch. Painted with automotive paint.

Anime: Saint Seiya: The Lost Canvas
Character: Alone (Hades)
made by: :icondionysus80:





:star: Facebook :star: GS Props :star:
Show
Add a Comment:
 
No comments have been added yet.

Finally here's the long awaited ScannerJOE's version of the Daft Punk Thomas' helmet.

The file is at [link] it includes pepakura, blender, and manual files.

This is not like any other papercraft as it introduces my new technique to build spheric surfaces using thick cardboard (around 2mm), WITHOUT USING MACHE.

This is the one shown at [link] and [link]

Enjoy it!
Show
Add a Comment:
 
No comments have been added yet.

This is a comission from ~snuffle12321 that i decided to make because it was seen easy and fun.

The file is at [link]

Your questions are wellcome but please check the readme.txt file before asking.

Enjoy!.
Show
Add a Comment:
 
No comments have been added yet.

If you're an "old" geek like me, you'll appreciate this model from the 80's series Voyagers. I actually built a papercraft of it in my childhood but it wasn't as accurate like this one.

You can find the papercraft model and Blender files at [link]

Enjoy it as much as i do now!.
Show
Add a Comment:
 
No comments have been added yet.

Template for the Toon 10th Doctor Who i designed with my fellow artist mech-monkey.The long coat is optional and that is why you have extra arms.
Show
Add a Comment:
 
No comments have been added yet.

Template for my 11th Doctor Who paper toy which i created with the help of mech-monkey. If you download it and build it please put up pictures.
Show
Add a Comment:
 
No comments have been added yet.

Jack Sparrow paper model designed by me and my mate mech-monkey.Please note credit where crredits due i just did a few sketches mech-monkey made the template and did all the hard work. We will make the template available if we have enough interest.Let us know what you think in the comments.
TEMPLATE NOW AVAILABLE IN MY GALLERY IF YOU DOWNLOAD IT PLEASE LEAVE A COMMENT THANK YOU.
Show
Add a Comment:
 
No comments have been added yet.

Mewtwo papercraft. Rip by Ignatus, templates by OliGig and testbuild by me. I know neither where nor when it'll be released, this is up to OliGig.
Show
Add a Comment:
 
No comments have been added yet.

These were the Halloween special models of Paperpokes.

The are perfect ain't they? Thanks to :iconz8-0:

When I first saw them, still on the pdo, I felt in love, it's really cool and great to have these models built XD In special The regular one, IT'S PERFECT! The six legs were really hard to build, placing the gold parts were a pain, but I must say, IT'S WORTH :D I haven't even noticed all the legs when I first saw the pdo, just found out that there were six legs when :iconz8-0: told me XD

The origin form chibi proofs that not all the chibis are easy to build, in fact, this one is really hard. The gold parts and the spikes were REALLY hard to build, but if it were more simple would look a lot weird.

The Altered form would be easy if it wasn't for the neck gold parts, in special the middle ones.

All of them are perfect and stay perfect together :D

They can be downloaded at Paperpokes:
Regular Giratina: [link]
Chibi Origin Form Giratina: [link]
Chibi Altered Form Giratina: [link]

Have fun building them :D They are hard but it's really worth having them XD
Show
Add a Comment:
 
No comments have been added yet.

Wes papercraft

This one can be downloaded here: [link]

Edited by :iconz8-0:

This is one of the hardest models I've ever built, even harder than Rui [link] :D But the result is totally worth, in fact, it's one of my favorite models :D The pose is also amazing :D

Tip, be carefull at the hands, they are the worst part.
Show
Add a Comment:
 
No comments have been added yet.